Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Search

Recent Posts on TrailTalk
Gen I 1989 Broken Hood Latch Solved!
by B_Line - 01/21/21 04:16 PM
1989 Montero Broken Hood Latch Cable!
by polar - 01/14/21 08:40 PM
torsion bar question
by rxinhed - 01/14/21 02:07 AM
suzi the psychic
by rascott - 01/11/21 06:28 AM
Sway Bar delete.. ???
by Trailmonkey - 01/07/21 05:29 PM
Vet over his Head
by chadzeilenga - 01/04/21 03:56 PM
‘89 Monty SWB - 1100 idle at start, -500 eventual
by chadzeilenga - 01/04/21 03:51 PM
Support 4x4Wire
New Topics on TrailTalk
Gen I 1989 Broken Hood Latch Solved!
by polar - 01/14/21 08:42 PM
torsion bar question
by tcb762 - 01/12/21 11:02 PM
‘89 Monty SWB - 1100 idle at start, -500 eventual
by BrooklynOpus - 01/04/21 03:14 PM
SOLD! New 1990-1995 Toyota 4Runner 4Dr Carpet
by code33 - 01/03/21 03:52 AM
Vet over his Head
by SATXGuy - 01/02/21 05:07 AM
KM145: What have I done wrong?
by TresMon - 12/28/20 05:45 PM
4x4 Gallery
Photos of rig
Attila
99 Monterrible Sport
Scar the Cylon Raider
Mercenary Sergeant: Code Name "Sapphire"
More News on the 'Wire

4x4Voice
4x4Wire
MUIRNet-News
OutdoorWire
Who's Online Now
0 registered members (), 62 guests, and 5 spiders.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums37
Topics138,168
Posts1,080,941
Members15,144
Most Online907
Dec 28th, 2019
Previous Thread
Next Thread
Print Thread
Rate Thread
Need a better axle shaft remover #1076264 01/12/15 03:27 AM
Joined: Aug 2014
Posts: 173
danz91crx Offline OP
Wheeler
Was trying to pull the rear axle shafts on a 1990 Mitsubishi Montero. Removed the 4 bolts holding it to the axle housing and proceeded to attach my semi home made puller to the hub. I had a harbor freight blind hole bearing puller as my only slide hammer. I attached it to the hub with a piece of angle iron with 3 holes in it. Two hole on the outside for wheel studs across from each other to go through and on in the center to attach the 3lb slide hammer. After an hour of beating on it and it not budging I gave up. Even tried heating the housing a bit with propane torch. Any suggestions on what exactly I should get to do this right?


1990 LWB RS A/T
1990 LWB Base A/T
1991 LWB LS A/T Going...Going...
Support our sponsors
Re: Need a better axle shaft remover [Re: danz91crx] #1076265 01/13/15 12:57 AM
Joined: Feb 2000
Posts: 6,231
4x4Wire Offline
Trail Leader
***
Is there a retainer in the diff that keeps the axle in place????

Re: Need a better axle shaft remover [Re: 4x4Wire] #1076266 01/13/15 07:51 AM
Joined: Aug 2014
Posts: 173
danz91crx Offline OP
Wheeler
No, they are suppose to come out when unbolted. Its got the cover/diff assembly on the front pinion side and there would be no way to get at retainers if it had them.


1990 LWB RS A/T
1990 LWB Base A/T
1991 LWB LS A/T Going...Going...
Re: Need a better axle shaft remover [Re: danz91crx] #1076267 01/13/15 10:13 AM
Joined: Feb 2000
Posts: 6,231
4x4Wire Offline
Trail Leader
***
Have you done a site search for hints others have posted? The Mitsubishi section does have several faqs that may help. There are several very knowledgable guys with Mitsubishi experience.

Re: Need a better axle shaft remover [Re: 4x4Wire] #1076268 01/13/15 07:39 PM
Joined: Aug 2014
Posts: 173
danz91crx Offline OP
Wheeler
Yeah, I did look and did a site search with google for a post also have the factory service manual. Looks pretty straight forward I think its just that I maybe need to use better tools. Like a 5-10lb slide hammer might work rather then my 3lb. I'll try asking in the Mitsubishi section

Thanks


1990 LWB RS A/T
1990 LWB Base A/T
1991 LWB LS A/T Going...Going...

Moderated by  4x4Wire, Mike Bondi, PajEvo 







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.2.34 Page Time: 0.027s Queries: 15 (0.007s) Memory: 2.8426 MB (Peak: 3.1636 MB) Data Comp: Off Server Time: 2021-01-23 11:11:13 UTC
Valid HTML 5 and Valid CSS